Maytag Error Codes

It can be worrying when an error code shows up on your Maytag machine and you don’t know what it means – our tables below will let you diagnose the problem.

Model: FRONT/L

Fault Code	Fault
8	MOTOR NOT TURNING DURING WASH CYCLE
8	10	MOTOR SENSED NOT TURNING DURING SPIN CYCLE
17	10	DOOR WAS NOT LOCKED AT THE END OF THE FINAL SPIN
17	19	WATER LEVEL REACHED BUT NOT MAINTAINED DURING CYCLE
30	19	SHUT DOWN DUE TO MOTOR SPEED ERROR DURING WASH
30	31	SPIN CYCLE WAS DELAYED AS WATER STILL IN DRUM
32	31	UNBALANCE BELOW 500RPM
32	33	SUDS DETECTED DURING WASH CYCLE
34	33	SPINNING BELOW 85RPM TOO LONG DURING SPIN CYCLE
34	35	TUMBLING ABOVE 50RPM TOO LONG DURING WASH CYCLE
36	35	MOTOR NOT SLOWING DOWN AFTER 120SEC'S OF COASTING AFTER REACHING 300RPM
36	37	SPEED ERROR, MOTOR RUNNING TOO FAST,COULD BE OPTIC SENSOR AT FAULT
39	37	MOTOR STILL RUNNING AFTER 120SEC'S OF COASTING AFTER UNBALANCE
39	40	MOTOR RUNNING FASTER THAN 85RPM AND DOOR NOT LOCKED
71	40	DEBIT CARD READER MESSAGING PROBLEM
71	74	DEBIT CARD READER MESSAGING PROBLEM
75	74	DEBIT CARD READER MESSAGING PROBLEM
75	1b	SLOW FILL LEVEL NEVER REACHED
1d	1b	UNBALANCE WITHIN SPIN GREATER THAN 500RPM AND LESS THAN 675RPM
1d	2A	MOTOR ON A FULL POWER FOR 15SEC'S DURING FINAL SPIN
2F	2A	SHUT DOWN DUE TO MOTOR SPEED ERROR DURING SPIN
2F	d10	DOOR LOCK SENSE ERROR,SPINS INHIBITED
d11	d10	SPEED ERROR,COULD BE OPTIC SENSOR AT FAULT

Model: L/C

Fault Code	Fault
d1	DRIER DOOR SENSE ERROR
d1	d2	WASHER DOOR SENSE ERROR
d4	d2	DRIER MOTOR CONTROL CIRCUIT ERROR

Model: TOP/L

Fault Code	Fault
d1	WATER LEVEL DETECTION ERROR ON CONTROL BOARD
d1	d12	MOTOR SENSE ERROR DETECTED ON CONTROL BOARD

Model: STACK D

Fault Code	Fault
d12	LOWER MOTOR SENSOR CIRCUIT FAILURE
d12	d14	UPPER MOTOR SENSOR CIRCUIT FAILURE
d18	d14	UPPER THERMISTOR CIRCUIT FAILURE
d18	d19	UPPER DRIER TEMP TOO HIGH
d2	d19	LOWER THERMISTOR CIRCUIT FAILURE
d2	d20	UPPER DRIER MOTOR CONTROL CIRCUIT FAILURE
d21	d20	LOWER MOTOR SENSED RUNNING WHEN IT SHOULD BE OFF
d21	d22	UPPER MOTOR SENSED RUNNING WHEN IT SHOULD BE OFF
d23	d22	CONTROL BOARD IS NOT CALIBRATED FOR THERMISTORS
d23	d3	LOWER DRIER TEMP TOO HIGH
d4	d3	LOWER DRIER MOTOR CONTROL CIRCUIT FAILURE

Model: ALL

Fault Code	Fault
d13	BLOCKED COIN 2
d13	d16	CONTROL NOT RECEIVING COMMUNICATIONS FRON DEBIT CARD READER
d4	d16	WASHER LID SENCE ERROR ON CONTROL BOARD
d4	d5	BLOCKED COIN 1
d7	d5	LAST FILL WAS SLOW
d7	d8	LAST DRAIN DURING FINAL SPIN WAS SLOW
d9	d8	VOLTAGE BELOW 90Vac FOR 8 SECONDS

Model: HELP MODE SYMBOLS MAYTAG WASHER FRONT LOADER MAH14 MODELS

Fault Code	Fault
DISPLAY=WASH	WATER SENSED AT WATER LEVEL
DISPLAY=WASH	DISPLAY=*	LOW VOLTAGE PRESENT(BELOW ABOUT 90 VAC)
DISPLAY= RE	DISPLAY=*	REDISTRIBUTING OUT OF BALANCE LOAD(CHECK OUT OF BALANCE SWITCH WIRING) IF NO MOTOR ACTION BUT OUT OF BALANCE SYSTEM CHECKED CHECK MOTOR/CONTROL RECIRCULATION PUMP RELAY ON
DISPLAY= RE	DISPLAY=CIRCLE ABOVE DIGIT	DOOR CLOSED
DISPLAY=DOOR LOCKED	DISPLAY=CIRCLE ABOVE DIGIT	DOOR SENSED LOCKED
DISPLAY=DOOR LOCKED	DISPLAY=COLD	COLD WATER RELAY ON
DISPLAY=HOT	DISPLAY=COLD	HOT WATER RELAY ON
DISPLAY=HOT	DISPLAY=SOFTENER	DOOR LOCK RELAY ON SOFTENER DISPENSE RELAY ON
DISPLAY=BLEACH	DISPLAY=SOFTENER	DRAIN RELAY ON BLEACH RELAY ON
DISPLAY=BLEACH	DISPLAY= UNBALANCE	REDISTRIBUTING OUT OF BALACE LOAD(CHECK OUT OF BALANCE SW WIRING)
DISPLAY= OR	DISPLAY= UNBALANCE	DOOR LOCK RELAY ON
DISPLAY= OR	DISPLAY=AVAILABLE	DRAIN RELAY ON

Model: MAYTAG FRONT LOADER

Fault Code	Fault
8	MOTOR SENSED NOT TURNING DURING WASH
8	F	SUDS LOCK POSSIBLE MCH OVERLOAD WHEN SPINING LESS THAN 500 RPM
10	F	MOTOR SENSED NOT TURNING DURING SPIN CYCLE
10	17	DOOR NOT LOCKEDAT THE END OF FINAL SPIN CHECK MICRO SWITCH AND WIRING
19	17	WATER LEVEL WAS REACHED DURING THE WASH CYCLE BUT THE WATER LEVEL WAS NOT MAINTAINED SLOW FILL OR WATER DRAINING OUT OF THE TUB
19	1b	SLOW FILL WATER WAS NEVER REACHED LOW WATER PRESSURE FAULTY WATER VALVE TURN ON EX FILL FOR A LONGER FILL TIME IF WATER PRESSURE IS LOW
1d	1b	UNBALANCE WITHIN A SPIN AT GREATER THAN 500RPM AND LESS THAN 675RPM DURING THE FINAL SPIN CYCLE CHECK OUT OF BALANCE SWITCHES AND WIRING OR OUT OF BALANCE LOAD MOTOR ON FULL POWER FOR 15 SECONDS DURING THE FINAL SPIN AT 500RPM AND LESS THAN
1d	2A	675RPM POSSIBLE OVERLOADED MCH POSSIBLE LOSS OF A PHASE ON THE MOTOR
2F	2A	SHUT DOWN DUE TO MOTOR SPEED ERROR DURING SPIN FAULT WITHIN MOTOR ?
2F	30	SHUT DOWN DUE TO MOTOR SPEED ERROR DURING WASH CYCLE FAULT WITHIN MOTOR ?
31	30	SPIN CYCLE DELAYED WASH LEVEL SENSED FOR MORE THAN 60 SEC,S DRAIN PUMPFAULT ?
31	32	UNBALANCE AT LESS THAN 500RPM DURING THE FINAL SPIN, SPIN CYCLE STOPPED CHECK OUT OF BALANCE SWITCHES WIRING OUT OF BALANCE LOAD
33	32	SUDS DETECTED DURING WASH CYCLE
33	34	SPINNING BELOW 85RPM TOO LONG DURING THE SPIN CYCLE MOTOR FAULT?

Need assistance with your Maytag machine? Call us now on [ld_default] to book an engineer. We’re always here to help

Gary Slater

19:58 07 Aug 19

We have been using this company for many years to service and repair our Laundry Equipment nationwide, they have never let us down and the response time is excellent!! Good Guys!! Highly Recommended!!

Clive Cantrill

15:01 14 Sep 19

Very happy with my new stacker, super convenient and easy to use and takes up so little floor space. Impressed with functionality and ease of use. Gary programmed in our own programs

Reni Adebayo

14:10 14 Sep 19

It was a tricky installation. Other suppliers either declined or gave us ridiculous prices. The Aventus lads sorted it all out for us on the day. Great service, they couldn’t do enough for us.

shahin abbasi

15:31 14 Sep 19

Happy with my Danube washers and dryers. Polite and efficient installers. Looking forward to the wifi I've been promised.

Julian Lees

16:35 18 Aug 19

Tim Bellamy

14:22 01 Oct 19

I got a great CAD plan of my future laundry and all the equipment was fully explained. Price were reasonable. Easy to make a decision. And thankfully they were installed without hassle and they are working nicely. Good job and thanks.

Navi Sandhu

18:01 14 Oct 19

Nice installation of specially programmed machines in my Care home Replaced my old machines which my staff were struggling with. Quick process. Many thanks

darren

22:30 26 Sep 22

Very dishonest people.When I first contacted them I explained that I needed to buy some machines and needed something quite quickly.They told me what I needed to hear, it turns out they are salesman with no allegiance to their customer.I was told I'd receive machines in 3 weeks as they were already in stock and just needed to be shipped, 2 months later when I asked for a refund they refused and said it was a special order. It took over 3 months and responses during that time were slow to say the least. I'd advise using a more reputable company, especially if you're a smaller business as it can be costly with the wait times. For the money they cost me I'll be glad to return the favour, as reading reviews like this will put some potential future customers off dealing with them. The less than reputable people I encountered were Mike Ward and the company director Gary Flatt.