IPSO Error Codes

If you are having trouble with an IPSO model machine displaying an error code, have a look at our list below to find out what the issue is.

Model: M20/M9

Fault Code	Fault
"------------"	BOARD RESETTING,CUTOUT ON SPIN ? CHECK DOOR HANDLE/LOCK
"------------"	E4	WATER LEVEL NOT REACHED WITHIN 15MINS, WATER PRESSURE/DRAIN VAL
E5	E4	TEMP NOT REACHED WITHIN 80 MINS
E5	E6	DOOR UNLOCKED DURING WASH,FAULTY DOOR HANDLE/LOCK
E7	E6	WATER DIDN’T DRAIN TO ALLOW SPIN, DRAIN VAL OR BLOCKAGE
E7	E8	TEMPERATURE BELOW 5C OR ABOVE 95C FAULTY TEMPSENSOR TM140/204
EA	E8	TILT SWITCH ACTIVATED 15 TIMES, OUT OF BALANCE LOADING SHOCKERS DRAINAGE
EA	Eb	TILT SWITCH BLOCKED FAULTY

Model: M20

Fault Code	Fault
E3	EPROM ERROR INCORRECT CHIP OR FAULTY BOARD
E3	E9	MOTOR THERMAL PROTECTOR TRIGGERED
END	E9	DOOR FAILED TO OPEN,HANDLE/MECH OR SWITCHES
END	NOT2	SPEED ERROR CHECK WIRING IF PLUG IS FITTED/ SPEED SENSOR F7MAIN PULLEY LOOSE?TM215
NO DISPLAY	NOT2	CHECK DOOR LOCK HANDLE(DOOR LOCK MAYBE STUCK) THE DOOR MAYNOT OPEN !!!!!!!!!!!!!!!

Model: ALL

Fault Code	Fault
CLOSE	DOOR FAILED TO LOCK,HANDLE/MECH OR SWITCHES

Model: SIGMA

Fault Code	Fault
OFF ECHO	FAILED THERMAL CYCLE ,ENTER CODE AS FOLLOWS = PEPI SELECT(P) ECONOMY(E) SELECT (P) START ( I )

Model: PLC9

Fault Code	Fault
1tE/2tE	REQD TEMP WASN’T REACHED
1tE/2tE	3tE	REQD TEMP WASN’T REACHED
cdo	3tE	DOOR NOT CLOSED,INSPECT DOOR LOCK/HANDLE
cdo	4tE	REQD TEMP WASN’T REACHED
E9	4tE	MOTOR TOC ACTIVATED
E9	HLE at start	AT THE START WATER LEVEL SWITCH FAULT HLE = HIGH LEVEL LLE LOW LEVELOR SLE-TILT
HLE during wash	HLE at start	WATER LEVEL NOT REACHED (HLE HIGH LEVEL) ( LLE LOW LEVEL)
HLE during wash	SLE at start	LEVEL SWITCH MAY BE FAULTY/AIR DOME BLOCKED
SLE-tilt	SLE at start	WATER LEVEL NOT REACHED

Model: PC30

Fault Code	Fault
Error=04	FILLING TIME LONGER THAN 15MINS
Error=04	Error=05	TEMP NOT REACHED WITHIN 60 MINS
Error=06	Error=05	DOOR LOCK RELEASED DURING THE PROGRAM
Error=06	Error=07	WATER IN THE TUB AFTER THE PROGRAM
Error=08	Error=07	TEMP SENSOR FAILURE OR TEMP OUT OF RANGE
Error=08	Error=09	THERMO-MAGNETIC PROTECTION WAS ACTIVATED
Error=10	Error=09	TILT SWITCH WAS ACTIVATED
Error=10	Error=11	WATER STILL IN DRUM AT START OF PROGRAM
Error=12	Error=11	WATER STILL IN DRUM 3MINS AFTER DRAIN,HEATING NOT ACTIVATED
Error=12	Error=13	REMOVE MOTOR WIRING IF INVERTER STILL ALARMS (INVERTER FAULTY)

Model: PS40

Fault Code	Fault
A2	UNKNOWN PROGRAM SELECTED
A2	A4	FILLING TIME LONGER THAN 15MINS
A5	A4	TEMP NOT REACHED WITHIN 60 MINS
A5	A6	DOOR LOCK RELEASED DURING THE PROGRAM
A7	A6	WATER IN THE TUB AFTER THE PROGRAM
A7	A8	TEMP SENSOR FAILURE OR TEMP OUT OF RANGE
A9	A8	THERMO-MAGNETIC PROTECTION WAS ACTIVATED,NON INVERTER M/C'S ONLY
A9	Ab	WATER STILL IN DRUM AT START OF PROGRAM
Ac	Ab	WATER NOT DRAINED WITHIN 3MIN'S,THERE WAS NO FURTHER HEATING
Ac	Ad	NO RPM MEASURED DURING THE SPIN,INVERTER M/C'S ONLY
AH	Ad	TILT'S PREVENTED SPIN
AH	F5	THE DOOR WAS OPEN DURING THE PROGRAM
F6	F5	THE DOOR WAS UNLOCKED DURING THE PROGRAM
F6	FA	TILT SWITCH BLOCKED

Model: 6000

Fault Code	Fault
E9	MOTOR OVERLOAD CURRENT (DRAWN ABOVE 8AMP FOR 6000) TRIAC ON MOTOR BOARD MUST BE BTB NOT BTA
E9	NOT 3	5000 HRS ,CARBON BRUSHES REQD
NOT1/ "OOO"	NOT 3	MOTOR OVERLOAD/MOTOR BOARD
NOT1/ "OOO"	NOT2	TACHO FAULT ON MOTOR,CHECK CIRCUIT
NOT2 /"OOO"	NOT2	SPEED ERROR,CHECK MOTOR BOARD/WIRING

Model: DIRONER

Fault Code	Fault
HEAT	TEMP BELOW 4oC OR ABOVE 190oC
HEAT	NO AIR	AIR FLOW SWITCH NOT O/C
NO HEAT	NO AIR	HEAT NOT DETECTED 10SEC'S AFTER IT WAS ACTIVATED
NO HEAT	NO SPEED	SPEED DETECTOR NOT SENDING SIGNAL FOR SPEED

Need assistance with your IPSO machine? Call us now on [ld_default] to book an engineer. We’re always here to help

Gary Slater

19:58 07 Aug 19

We have been using this company for many years to service and repair our Laundry Equipment nationwide, they have never let us down and the response time is excellent!! Good Guys!! Highly Recommended!!

Clive Cantrill

15:01 14 Sep 19

Very happy with my new stacker, super convenient and easy to use and takes up so little floor space. Impressed with functionality and ease of use. Gary programmed in our own programs

Reni Adebayo

14:10 14 Sep 19

It was a tricky installation. Other suppliers either declined or gave us ridiculous prices. The Aventus lads sorted it all out for us on the day. Great service, they couldn’t do enough for us.

shahin abbasi

15:31 14 Sep 19

Happy with my Danube washers and dryers. Polite and efficient installers. Looking forward to the wifi I've been promised.

Julian Lees

16:35 18 Aug 19

Tim Bellamy

14:22 01 Oct 19

I got a great CAD plan of my future laundry and all the equipment was fully explained. Price were reasonable. Easy to make a decision. And thankfully they were installed without hassle and they are working nicely. Good job and thanks.

Navi Sandhu

18:01 14 Oct 19

Nice installation of specially programmed machines in my Care home Replaced my old machines which my staff were struggling with. Quick process. Many thanks

darren

22:30 26 Sep 22

Very dishonest people.When I first contacted them I explained that I needed to buy some machines and needed something quite quickly.They told me what I needed to hear, it turns out they are salesman with no allegiance to their customer.I was told I'd receive machines in 3 weeks as they were already in stock and just needed to be shipped, 2 months later when I asked for a refund they refused and said it was a special order. It took over 3 months and responses during that time were slow to say the least. I'd advise using a more reputable company, especially if you're a smaller business as it can be costly with the wait times. For the money they cost me I'll be glad to return the favour, as reading reviews like this will put some potential future customers off dealing with them. The less than reputable people I encountered were Mike Ward and the company director Gary Flatt.